This is Style #3 of three different kit styles we offer based on desired valve and hose routing locations. On this style kit the selector valve and all hoses are mounted and concealed under the operators platform for later model 200 and 400 series tractors with "full fenders and full operator floor and platform" (like in photos) as well as for most 3000 and 4000 series tractors and some loaders. But for plug and play on older 200 and 400 series tractors we recommend our STYLE #1 or STYLE #2.
WHAT DO OUR SELECTOR VALVE KITS DO AND ARE USED FOR? THEY LET YOU INDEPENDENTLY OPERATE YOUR 3 POINT HITCH FROM YOU MID/FRONT LIFT HYDRAULICS! WE VERY HIGHLY RECOMMEND THIS ON ANY AND ALL TRACTORS EQUIPPED WITH 3 POINT HITCHES. A MUST HAVE SO YOU CAN USE BOTH REAR AND FRONT/MID MOUNTED ATTACHMENTS INDEPENDENTLY! Lift the rear attachments when you want and the front or mid attachments when you want instead of both at the same time.
Lifting both at the same time without a selector valve is unproductive, frustrating as well as dangerous. This style #3 of 3 styles we offer, again be sure to look at all 3 to see what one will work best for you!Look where the hoses and valve is located on in EACH different kit and see if you have room to mount the valve and run the hoses where they need to be for each style kit. It is up to you to pick the correct kit for YOUR tractor as they all vary to some degree. Our kits are plug and play, very simple installs with basic tools and skills. Our kits are made of top quality parts, no hacking or cutting of the tractor is necessary to install. Depending on what kit number of ours only 2 or 3 holes have to be drilled to end up with a clean professional look that will last a very long time.
All of OUR hoses have expensive swivels on BOTH ends for ease of install and maintenance, also with swivels on both ends and the correct expensive hose ends on our hoses there is no need for extra adapters on the selector valve. And in most cases the other end of the hoses thread right on to your existing tractor fittings. All our fittings are quality fittings/hoses ends are made for high hydraulic pressure, NO cheap dangerous pipe fittings here. The hoses are all high quality very flexible high PSI R17 hydraulic hoses and ends. All kits Include one high quality selector valve, three high quality 1/4 hoses made to length for each particular kit install.A cap fitting for the TCV "TEE", a 45 degree and a straight fitting that MAY need to be used depending on how your tractor already is set up. Also included is all necessary grade 8 hardware, basic hose protection for exposed portions of hose as well as zip ties for mounting and securing hoses and hose protection. Basic guidelines and photos for installation are also included.
Only very basic tools are needed, most installs only require 1/2, 9/16, 5/8, 11/16, 3/4 wrenches. And possibly basic internal hex style Allen wrenches or sockets to remove plugs in Selector valve. Most installs take around 30 mins depending on skill.
So we try to keep the inventory for online sales as accurate as we can. But sometimes there is an overlap.We just wanted to be upfront about that. You can message us to check current inventory. As stated this kit Style #3 and is mainly used and recommend for later 200 and 400 as well as 3000 and 4000 series tractors with full covered floor platforms like in photos. Some installers had success mounting it on earlier style and model tractors with possibly some modification to tractor foot rest and or custom hoses being made by installer at installers expense. Only the 3 included specific lengh hoses for suggested location are included. These are our 3 different style kits that we use at our shop to install selector valves on Case Ingersoll tractors/loaders equipped with HH34 and H26, J26 or LT26 3 point hitches. Used on most models made by CASE INGERSOLL from the 200, 400, 600, 3000 and 4000,4100, 4200, 6000, 7000 series tractors and their sub models.
Being that they do fit many models including small and big tire models as well as long and short frame, loader tractors and multiple Case Ingersoll 3 point hitch models, there MAY BE some slack/extra length to hoses or there may be little to none at all. We have yet to have a issue using this kit on any Model Case Ingersoll models. The way you choose to route, hang, tie, secure and protect your hoses will also determine the amount of slack that is in the lines as there are many options as how to do this. Fits many of these CASE INGERSOLL Models later 200/400/600 and 3000/3100/4000/4100/4200, 6000/7000 series tractors.Case Ingersoll tractor later models of 220, 222, 224, 226 most 3012, 3014, 3016,3018,3116,3118,3120. Later model years 444, 446, 448 most 4016, 4018, 4020, 4116, 4118, 4120, 4200 series models some 644, 646, 648 some 6018, 6020, 7020 and more models.
ALSO LOOK AT OUR OTHER MULTIPLE STYLE "SELECTOR VALVE" INSTALL KITS THIS IS ONLY 1 OF 3. WE ALSO HAVE THREE POINT HITCH INSTALL/MAINTENANCE KITS TOO.
And many other Case Ingersoll items. It is up to you to make sure this fits YOUR tractor before purchasing, THANK YOU. What is pictured and the main item in picture (not background) is what you get, Ask If I can help you in any way. Follow us on Face Book at Case Ingersoll Garden Tractors North East. It is solely the purchasers responsibility to choose qualified trained professionals for correct and safe product installation and.
So please feel free to ask questions if you need to and we will help to the best we can and THANK YOU. If you have any issues please reach out and contact me. The item "Case Ingersoll COMPLETE SELECTOR VALVE KIT for 3 point hitches Kit Style #3" is in sale since Saturday, April 24, 2021. This item is in the category "Home & Garden\Yard, Garden & Outdoor Living\Lawn Mowers, Parts & Accessories\Lawn Mower Parts". The seller is "rocklandvalleyfarm" and is located in Andover, Connecticut.This item can be shipped to United States.